TheGasMaker.com, Run your car on water

Check out our comparison videos below.

We compare 7 different configurations.

thegasmaker.com started with the plan to bring to the public the most efficient HHO generator

at the lowest possible pricing, We have done exactly that. Our research still never stops.

11 plate-3 holes 3.5" plates-1/4" hose barbs-inlet/outlet at top of cell

************

11 plate-3 holes 3.5" plates-3/8" hose barbs-inlet/outlet at top of cell

************

11 plate-3 holes-3.5 plates-1/4" hose barbs-inlet at bottom/outlet at top of cell

************

9 plate-1 hole alternating holes top to bottom 3.5" plates-1/4" hose barbs-inlet at bottom/outlet at top of cell

************

9 plate-1 hole alternating holes top to bottom 3.5" plates-1/4" hose barbs-inlet/outlet at top of cell

************

21 plate-3 holes 3.5" plates-1/4" hose barbs-inlet/outlet at top of cell

************

11 plate-3 holes 6" plates-1/4" hose barbs-inlet/outlet at top of cell

You can see for yourself why we sell the DRY CELL that we do.

It is not because we just added a plate or copied someone else's idea.

It is because we put time and money into research.

We always have, from the very beginning 3 years ago.

Please watch all the videos below before you make a decision to spend your money.

All testing was done with same variables

3 oz's of KOH

34 oz's of distilled water

battery power source 13.2 volts

Fluke Ammeter

The same LPM gauge (may vary with your gauge)

NO PWM

All cells ran for approximately 30 minutes before taking a reading

You will see that you basically get a set amount of HHO from a certain amount of AMPS

The size or number of plates has very little to do with production.

The only time it does is if you go below 3.5" plates, then efficiency diminishes.

I would suggest that before buying any HHO dry cell you know the number of plates and configurations used. Any legitimate HHO generator site should have this information in their description.

Thank you and enjoy!!!!

11 plate-3 holes 3.5" plates-1/4" hose barbs-inlet/outlet at top of cell

11 plate-3 holes 3.5" plates-3/8" hose barbs-inlet/outlet at top of cell

11 plate-3 holes-3.5 plates-1/4" hose barbs-inlet at bottom/outlet at top of cell

9 plate-1 hole alternating holes top to bottom 3.5" plates-1/4" hose barbs-inlet/outlet at top of cell

9 plate-1 hole alternating holes top to bottom 3.5" plates-1/4" hose barbs-inlet at bottom/outlet at top of cell

21 plate-3 holes 3.5" plates-1/4" hose barbs-inlet/outlet at top of cell

11 plate-3 holes 6" plates-1/4" hose barbs-inlet/outlet at top of cell

As stated above all of the HHO dry cells tested were done with the same electrolyte (catalysis) mix of approximately 10%, which is what is recommended for maximum efficiency. You will no doubt run across other HHO generator "salesmen" proclaiming to give you 1 liter per minute for every 10 amps drawn by the HHO Dry Cell, this is done by adding more KOH. As you can see by the HHO test videos above, that formula is somewhat true, (Except with the 9 plate "one hole") this HHO unit was completely unstable.

The three important issues most HHO Dry Cell salesmen forget to tell you are:

The more amps you push through your HHO Dry Cell the more heat you generate. Heat = steam not HHO gas.

By running your HHO Dry Cell at high amps you will no doubt need to rebuild or replace it much sooner.

After about 20 amps drawn on a single circuit in your vehicle you are taxing your alternator, therefore diminishing your gains.

Call 423-312-9295 between 10am and 10pm est. for questions

MAKE SOME CASH

If you are looking to get into the HHO business,

this is the perfect product for you to resell.

They are attractive and easy to install.

You can easily resell for over $100.

We offer wholesale discounts for orders of 10 or more.

We do not charge for a distributer license.

Become a Distributer